Table of Content
The best way to power cycle your phone is to disconnect and reconnect the battery. During reassembly, you will need to reinstall the Touch ID cable bracket. The top of the bracket needs to slide between the battery and Touch ID cable connector, in front of the metal tab. The bottom must latch down over the connector. With a plastic opening tool, gently pry the edges of the rear case down, away from the front panel assembly, while you pull up with the suction cup.
There is a tiny metal guard underneath, make sure you hold it in place so the cable doesn't spin or tear underneath it. Also make note of the orientation of this guard as you'll need to replace it again during re-assembly. You only want to separate the screen about an inch at this point. You'll need some tools and parts in order to repair your iPhone 5s, including the replacement assembly.
Black home button + flex cable, replacement part for Apple iPhone 6
Just be careful not to tear the gasket while doing this. The display assembly should now be free from the body of the phone. Go ahead and set everything but the display assembly aside now. Now use your spudger tool in order to remove the three cables shown in the image below. You'll need to remove the two off to the far right in order to reveal the third and final cable, which sits below them. @schuft That’s a fairly involved repair, but yes!
While you apply the pressure, click the home button. Remove the cable, and see if that fixed the problem. Thus I got a home button replacement from hcqs.cc and have a repair man replace the old one.
Step 1
If you're still within the provided one-year warranty and your phone doesn't show signs of accidental damage, head on over to Apple. As long as you're covered by warranty, the company will replace your phone or perform any necessary repairs. Now snap the display back down and into place. Be sure to line up the grooves in the top of the screen inside the frame. If you are facing resistance, do not force the display down. Make sure everything is lined up properly and that the clips in the top are aligned properly.
Replace the two #000 screws on either side of the Home button assembly using your #000 screwdriver again. This time, be sure not to screw the two screws in too tight. If you do, it can prevent the Home button from depressing correctly. You want the screws to be firmly in place but not tight.
Removing the Touch ID cable bracket
When it does, let go of the sleep button and hold down the home button. For DIYers who would rather attempt repairs themselves, we offer these guides. When you press the buttons, you'll see the Volume under the indicator. When you're not using other apps, the buttons will adjust the ringer volume and you'll see Ringer under the indicator.
Lay overlapping strips of clear packing tape over the iPhone's display until the whole face is covered. Remove the two 3.9 mm Pentalobe screws from either side of Lightning connector. Use this guide to replace the home button assembly in your iPhone 5s. Offer a safe and simple way to fix iOS system errors without data loss. Well, be careful to open your iPhone 5S and replace its Home button. Otherwise, you may need another guide to help you fix new busted iPhone parts.
Four ways to fix an unresponsive iPhone home button
During reassembly, use the flat end of a spudger to snap the front portion of the Touch ID cable bracket down over the cable connector. If you’ve had your phone cracked or shattered, then it’s definitely worth fixing. Not only will it make your phone look and feel better, but you could also be saving a lot of money on repairs. Third, connect your phone to a power cord and plug it into an outlet. Fourth, hold down both sides of the phone and lift up.
Instead, be sure that the top is lined up correctly and that you aren't snagging any cables. There should be no resistance when snapping it back into place. If there is, you aren't lining it up correctly. Now simply swap the new Home button flex in the old one's place. If you ordered the parts I've recommended above from eTech, the home button is already in place. If you ordered from elsewhere and got only a flex, you'll have to transfer the Home button and gasket over to the new flex.
However, many people feel that it is worth the inconvenience and expense to fix a broken phone screen. Apple’s screensavers are actually quite simple. They use a small image that appears on the main display of your iPhone when you’re not using it, and then they fade in and out over time.
These screws can be accessed without removing the entire phone, but they’re easier to remove if they’re accessible from the front. One way to fix your iPhone’s screen is to try and pry the glass off with a knife or other sharp object. But if that doesn’t work, then you could try using a plunger to suction onto the glass and pull. If there are any plastic arms or clips that hold your phone together, remove them and try to put them back in place with pliers if possible. If you’re having trouble fixing your iPhone screen, it might be time to take a look at some of the remedies that are available. These include things like using a cleaning cloth and soap, using a vacuum cleaner, and using a hairdryer.
This error renders your iPhone useless as it bricks it. Too bad you can not buy a home button, and a new paired chip. Even if you could replace the A7 chip, it would not be worth the cost involved. I have a slight faint movement when touching the home button lightly. Nothing happens, but I am sure it will only get worse, and the home button will quit working.
No comments:
Post a Comment